The Transformers Archive Skip to main content / Also skip section headers

[The Transformers Archive - an international fan site]
Please feel free to log in or register.

 
  • transformers toys
  • transformers comics
  • transformers cartoon
  • transformers live-action movies
  • transformers fandom
  • transformers forum

Go Back   TFARCHIVE > TRANSFORMERS > Transformers Toys & Merch

Reply
 
Thread Tools
Old 2017-12-01, 12:47 PM   #21
Clay
"I've done better and got over it."
 
Clay's Avatar
 
Murray, KY
Smile

Does anyone know what kind of figure stands are compatible with the peg holes they've been including in most transformers for the past few years?

I know that the peg holes are included for that purpose, but I can't remember which stands they're designed for, or even if it matters.
 
Clay is offline   Reply With Quote
Old 2017-12-01, 07:04 PM   #22
Warcry
Likes Beast Wars toys. A lot.
 
Warcry's Avatar
 
Winnipeg, Manitoba, Canada
Default

They're the same sized peg as you'd find on Figmas -- I've currently got Misfire hanging out in jet mode on the stand that came with one of my Links. So anything that's marketed as compatible with them should work with Transformers too.

I'm fairly sure that Japanese stands have fairly standardized peg sizes, so it shouldn't be too tough to track some down that are compatible.
 
Warcry is offline   Reply With Quote
Old 2017-12-02, 02:12 AM   #23
Tantrum
Systems Analyst
 
Tantrum's Avatar
 
Aquidneck Island, RI, USA
Default

I've got a 3-pack of "Bandai Tamashii Stage Act.5 for Mechanics Clear" that work with TFs. All the other writing on the box is in Japanese. I had to tighten a screw to make it support a figure's weight, but have had no other problems. I think they're on Amazon.

The holes in TFs also fit the rods/pegs used by some Mega Blocks sets to make roll bars, exhaust pipes, and such.

I've attached a pic showing what you get and how I'm using it. Skybyte is the simplest, just a large rod plugged into the base. Highbrow has the large rod and base with two small rods and two hinges used to reach the top. Thundercracker doesn't have the mounting hole, so I have one of the flat claws grabbing his bot mode head to hold him steady. I took another flat claw, the last small rod, and some LEGO and Mega Blocks to make a 4th stand for Jetstorm.

In front are the other pieces. The 4 barely visible ovals are used to connect the bases to make a larger base. You can see the holes they connect to along the base edges. Then there's the 3rd hinge, 3 broad claws, and the 3rd flat claw.

My only complaint is that the holes on the bases are different sizes than those on the small rods, hinges, and figures. So, you can only plug large rods into bases, you can't use large and small rods to mount multiple small figures to the same base.
 
Attached Thumbnails
Click image for larger version

Name:	stands.JPG
Views:	19
Size:	448.5 KB
ID:	11714  

Alleged "poems"
that don't follow a rhyme scheme
are not poetry

Last edited by Tantrum; 2017-12-02 at 06:08 PM. Reason: added pic and description
Tantrum is offline   Reply With Quote
Old 2017-12-03, 11:18 PM   #24
Clay
"I've done better and got over it."
 
Clay's Avatar
 
Murray, KY
Smile

This is very helpful. Thanks!
 
Clay is offline   Reply With Quote
Old 2017-12-14, 08:18 PM   #25
Warcry
Likes Beast Wars toys. A lot.
 
Warcry's Avatar
 
Winnipeg, Manitoba, Canada
Smile

I completely forgot when I posted before, but I had a package of bootleg Tamashii stands (Act 4s I think, not Act 5s) slowly making their way from China. They finally showed up last night, and while I mainly got them for my Marvel figures, they work great for smaller Transformers as well. They're scaled for five- or six-inch figures, so Titan Master vehicles, Legends and Deluxes all work well with them.

They're all over eBay and I think I paid a bit over $1.50 a pop with free shipping. I don't even know what I'll do with all of the dozen I bought, but if I ever needed more I would be totally okay ordering more KOs. The quality is fine on all the ones I've set up so far, the joints are tight and the plastic isn't any more brittle than you'd expect from something this thin and clear. The only visible sign that they're fakes is the occasional air bubble inside (as you'll see on clear-molded TF accessories all the time) and some mold flash that wasn't properly cleared away, but is easy to clean up.

They also come with a lot of different bits (one articulated arm and one straight arm, an "extender" rod that you can use to raise the figures a bit higher and lots of different claw options). The bases are smaller than the ones Tantrum posted, but rectangular, so if you're looking to chain multiples together they'd be easier to work with than the Act 5's asymmetrical hexagon. You could probably get pretty creative combining different bits to count multiple figures per stand as well, but I'd imagine that balance would get pretty dicey quickly if they've got any mass at all.

The arms aren't as heavy-duty, though. I'm not sure they'd do a very good job holding up a Voyager-class figure. But they're a good option for smaller stuff.
 
Warcry is offline   Reply With Quote
Old 2017-12-20, 12:47 AM   #26
Tetsuro
One with the Matrix
 
Tetsuro's Avatar
 
Suomi Finland Perkele
Default

Say, is Thrust the only G1 conehead that actually had firing projectiles?

I've been thinking about getting the trio but the old Takara reissues are really pricey these days, but then I realized that it doesn't really make any difference with Ramjet and Dirge if neither one of them had any spring-loaded projectiles to nerf.
 
Tetsuro is offline   Reply With Quote
Old 2017-12-21, 09:16 PM   #27
Skyquake87
One with the Matrix
 
Skyquake87's Avatar
 
Default

Thrust is the only one with shooty missiles, yes. Whilst the original Takara reissues are expensive, the Platinum reissue set of all 3 from a couple of years back can be found cheaply enough.
 
Skyquake87 is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 12:02 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
 
 
[the-hub.co.uk]
[transfans.co.uk]
[oneshallstand]
[unicron.com]
[counter-x.net]
[ntfa.net]
[allspark.com]
[transformertoys.co.uk]
[tfu.info]
[botchthecrab.com]
[obscure_tf]
[tfradio.net]
 

[TFArchive button]
Link graphics...

BOOKMARK US
Or in FF, hit Ctrl+D.